![]() ![]() In this collection that you are being offered by us, you would come across an extensive range of Juice Bottle Label Templates that have been handpicked by us from a range of sources available on the internet. Have you been looking forward to getting hold of a few of the finest Juice Bottle Label Templates for your company? Well, if your reply is a yes then you would not regret visiting this page. (You might need to "cut" out the white area on the top image to see the first one.) But when your done it should look like this.Juice Bottle Label Templates | 31+ Free & Premium PSD | Ai | Vector | Eps Format Design Templates NOTE: If you want to print 2 images on the same label sheet, you can repeat the bove process and instead of printing you rotate the image 180° and paste it over the top of your first image. You should be able to print this no problem. (Or you can select your action in the action window and hit the "play triangle". From now on all you need to do is get you image and then hit the function key you selected in Step 3. ![]() In the Action Window you should see the "stop square" icon. You should now have an image that looks like this: Then minus off 2 * the printers margin (2 * 0.25 inch = 0.5 inch) from the height and the width. Again click on "IMAGE" -> "CANVAS SIZE.". So we will reduce our canvas size by that all the way around. Most printers have a 0.25 inch minimum margin (check your printers manual or look online). To insure that it clips of the blank areas and does not resize, will clip it so your printer doesn't need to choose. Most printers can not print to the edge of the page, so if you leave the canvas now, your printer will either clip the image off or rescale it to fit within its printable area. Also click on the top middle anchor point. This time leave the width as is, and change the height to the height of the label page (US = 11 inch and A4 is 297 mm). ![]() Finish positioning your image on the virtual page (Page Height)Īgain click on "IMAGE" -> "CANVAS SIZE.". Lastly (Item C), I click the bottom middle anchor point so that it centers horizontally, but adds the blank area at the top of the image. I then minus this from the margin (0.5 - 0.05 = 0.45) I just measured and add it to the height in the canvas window (4.7 + 0.45 = 5.15). (However, I made my image diameter slightly bigger than the cd label, so I am taking the difference between my resized image (Step 4 = 4.7 inch) and the actual cd label (4.6 inch) and dividing it in half (0.05). Next (Item B) we need to figure out the top margin (how far down from the top of the page in the edge of the cd label. First (Item A) you need to enter in the width of the label page (US Letter paper is 8.5 inches and Europe A4 is 210 mm. You'll need to fill in 3 things during this step. Start positioning your image on the virtual page (Horizontal & Top Margin)Ĭlick on "IMAGE" -> "CANVAS SIZE.". You might need to click off the "constrain proportions" check box. In my case I used 4.7 inches for the height and width and 300 for the resolution. I recommend using a slightly larger image than what the label actually is. In the Document Size area type in the height, width and Resolution you want. This will bring up the "Image Size" window. Then in Photoshop (with the image you want to use being the "active" window select "IMAGE" -> "IMAGE SIZE.". The Label I use has a diameter of 4.6 inches (117 mm). Use your ruler to measure the diameter of disk portion of your label. After naming and setting up your function key click on the "Record" button. This will bring up a window that allows you to name your action and setup Function Keys to make it easier to run your action when you are done. In the action window click on the "square on Square" icon (Create New Action - Item B in the picture). This will bring up a window that you can give a name to (maybe print actions). In the Action window click on the folder icon (Create New Set - Item A in the picture). I usually scan in the DVD at 300 dpi and the crop it so that there is not much white background to either side or top and bottom. We will be using Photoshop's "Action" menu to create a macro to size our image and place it on a virtual page so that when printed it fits perfectly on the label. Tools needed are: Adobe Photoshop, the labels you want to print on and a ruler. This is a guide on making CD / DVD Label templates in Adobe Photoshop 7.0 ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |